LPC1768 + 2.8" TFT ILI9325

Hello all,

I have an LCD module TM240320B9NFWUGWC and it has inbuilt ILI9325 
controller.
MPU-Interface Mode is through 8-bit parallel interface.

I'm trying to read its device code but  its not working, I always 
getting 0x0000. If any body can help on this, that will be very 
appreciated.

My code is as follow
------------------------------------------------------------------
void TSLCDInit(void) //initial LCD
{
   TSLCDOutIns(TS_INS_START_OSC);
    driver_code = TSLCDInDat();
    if (driver_code == 0x9320) //ILI9320
    {
      TSLCDInit9320();
    }
    else if (driver_code == 0x9325) //ILI9325
    {
      TSLCDInit9325();
    }
}
--------------------------------------------------------------------
But I am getting driver_code = 0x0000

And my write command, write data and read data as follow

void TSLCDOutIns(unsigned short ins) //write instruction to LCD
{
    LPC_PINCON->PINSEL0 &= ~(0xFFFF<<4);
    LPC_GPIO0->FIODIR |=  LCD_DATA_MASK;

    LCD_CS_LOW();
    LCD_RS_LOW();
    LCD_RD_HIGH();

    LCD_WR_HIGH();
    LCD_WR_LOW();
    delay_ms(1);
    LPC_GPIO0->FIOPIN &= ~LCD_DATA_MASK;
    LCD_WR_HIGH();

    LCD_WR_LOW();
    delay_ms(1);
    LPC_GPIO0->FIOPIN |= ins<<2;
    LCD_WR_HIGH();

    delay_ms(1);
}

void TSLCDOutDat(unsigned short dat) //write data to LCD
{
    LCD_RS_HIGH();
    LCD_RD_HIGH();
    LCD_WR_LOW();

    LPC_PINCON->PINSEL0 &= ~(0xFFFF<<4);
    LPC_GPIO0->FIODIR |=  LCD_DATA_MASK;
    LPC_GPIO0->FIOCLR = LCD_DATA_MASK;
    LPC_GPIO0->FIOSET = (dat >> 8) << 2;

    LCD_CS_LOW();
    LCD_CS_HIGH();

    LPC_GPIO0->FIOCLR = LCD_DATA_MASK;
    LPC_GPIO0->FIOSET = dat << 2;

    LCD_CS_LOW();
    LCD_CS_HIGH();
    LCD_WR_HIGH();

    LPC_PINCON->PINSEL0 &= ~(0xFFFF<<4);
    LPC_GPIO0->FIODIR &= ~LCD_DATA_MASK;
}

unsigned short TSLCDInDat(void) //read data from LCD
{
    unsigned short retval = 0;

    LPC_PINCON->PINSEL0 &= ~(0xFFFF<<4);
    LPC_GPIO0->FIODIR &= ~LCD_DATA_MASK;

    LCD_CS_LOW();
    LCD_RS_HIGH();

    LCD_RD_LOW();
    delay_ms(1);
    retval = (LPC_GPIO0->FIOPIN & LCD_DATA_MASK);
    LCD_RD_HIGH();
    delay_ms(1);

    LCD_RD_LOW();
    delay_ms(1);
    retval = (retval << 8) | (LPC_GPIO0->FIOPIN & LCD_DATA_MASK);
    LCD_RD_HIGH();
    delay_ms(1);

    LCD_CS_HIGH();

    return retval;
}

Note: For data lines I am using P0.2 to P0.9 and that's why I am 
shifting 'ins' and 'dat'  left by 2.

-Prakash
9886545216